Tiling your living room, bathroom, or kitchen is a part of home renovation project that gives your home a customized look that addresses your tastes and preference. Tiles have ability to improve the market value of your home. However, it will depend on the type of flooring material that is selected. The materials may range from wood laminate, carpet, or tile floors. These materials have their pros and cons. Therefore, it is important to choose one that addresses your needs. The procedure of custom tile flooring may seem to be a difficult task especially when you are doing it yourself. Nevertheless, with research and guidance from an expert you can do it successfully.
After identification of perfect flooring materials, the next step is to prepare your floor or wall. Old tiles should be replaced with cement backer board that will support new tiles. You should install a waterproof membrane to protect the backer board from being damaged by water. The waterproof membrane can be applied by use of a brush or a roller.
New tiles should be installed when the floor is clean and dry. Before purchasing the flooring material, you should measure the dimensions and calculate the size and number of material that you need during the tiling process. Ensure you purchase an excess of ten percent of the material to replace those that are likely to be damage during the installation process. You can consult an expert during the installation process.
The installation process must be started at the floor, if you are aiming at tiling both the wall and the floor. During this tiling procedure, you will need to cut the material to fit the recommended design. You will need to mark the starting point by installing a level board that begins from the right bottom corner and ends at the right top corner.
With the aid of a drill or a mixing paddle, prepare a thin-set-mortar that is suitable for your flooring materials. This step is the easiest since the manufacturers guidelines are labeled on the package. You should stir the mixture until a consistence similar to creamy peanut butter is achieved. The mixture is applied on the particular floor prior to laying the tiles.
Identify a starting point and begin the procedure of fitting the flooring materials. This step is critical since it will determine whether your floor will appear uniform. Always begin on the board that you installed. You will need to cut the tiles in case they do not fit.
The final stage is called grouting. It is done after the installation process. The materials are given twenty-four hours to set in properly. Mix the grout according to the manufactures instruction indicated on the package. Apply the grout in a sweeping motion and concentrate on the joints.
After identification of perfect flooring materials, the next step is to prepare your floor or wall. Old tiles should be replaced with cement backer board that will support new tiles. You should install a waterproof membrane to protect the backer board from being damaged by water. The waterproof membrane can be applied by use of a brush or a roller.
New tiles should be installed when the floor is clean and dry. Before purchasing the flooring material, you should measure the dimensions and calculate the size and number of material that you need during the tiling process. Ensure you purchase an excess of ten percent of the material to replace those that are likely to be damage during the installation process. You can consult an expert during the installation process.
The installation process must be started at the floor, if you are aiming at tiling both the wall and the floor. During this tiling procedure, you will need to cut the material to fit the recommended design. You will need to mark the starting point by installing a level board that begins from the right bottom corner and ends at the right top corner.
With the aid of a drill or a mixing paddle, prepare a thin-set-mortar that is suitable for your flooring materials. This step is the easiest since the manufacturers guidelines are labeled on the package. You should stir the mixture until a consistence similar to creamy peanut butter is achieved. The mixture is applied on the particular floor prior to laying the tiles.
Identify a starting point and begin the procedure of fitting the flooring materials. This step is critical since it will determine whether your floor will appear uniform. Always begin on the board that you installed. You will need to cut the tiles in case they do not fit.
The final stage is called grouting. It is done after the installation process. The materials are given twenty-four hours to set in properly. Mix the grout according to the manufactures instruction indicated on the package. Apply the grout in a sweeping motion and concentrate on the joints.
About the Author:
Ainsley G. Zaveri is a flooring specialist who helps individual homeowners make the best choices in getting their home flooring done economically. If you are interested in learning more about Custom Flooring Installations he recommends you check out kmfloorsinc.com
Aucun commentaire:
Enregistrer un commentaire